LitePlacer.com forums

I'm getting a Bad data in warning threshold error during nozzle calibration, however it doesn't say calibrationfailed.

If this an issue or not? Thanks:

Measuring nozzle, min. size 0.3, max. size0.5
CNC_A_m, a: 0
-- zero A movement command --
CNC_A_m, a: 22.5
==> {"gc":"G0 A22.5"}
{"r":{},"f":[1,0,18,77]}
{"sr":{"posa":0.005,"vel":63.95,"stat":5}}
{"sr":{"posa":22.500,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 45
==> {"gc":"G0 A45"}
{"r":{},"f":[1,0,16,75]}
{"sr":{"posa":22.505,"vel":63.95,"stat":5}}
{"sr":{"posa":45.000,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 67.5
==> {"gc":"G0 A67.5"}
{"r":{},"f":[1,0,18,77]}
{"sr":{"posa":45.005,"vel":63.95,"stat":5}}
{"sr":{"posa":67.500,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 90
==> {"gc":"G0 A90"}
{"r":{},"f":[1,0,16,75]}
{"sr":{"posa":67.505,"vel":63.95,"stat":5}}
{"sr":{"posa":90.000,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 112.5
==> {"gc":"G0 A112.5"}
{"r":{},"f":[1,0,19,78]}
{"sr":{"posa":90.005,"vel":63.95,"stat":5}}
{"sr":{"posa":112.500,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 135
==> {"gc":"G0 A135"}
{"r":{},"f":[1,0,17,76]}
{"sr":{"posa":112.505,"vel":63.95,"stat":5}}
{"sr":{"posa":135.000,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 157.5
==> {"gc":"G0 A157.5"}
{"r":{},"f":[1,0,19,78]}
{"sr":{"posa":135.005,"vel":63.95,"stat":5}}
{"sr":{"posa":157.500,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 180
==> {"gc":"G0 A180"}
{"r":{},"f":[1,0,17,76]}
{"sr":{"posa":157.505,"vel":63.95,"stat":5}}
{"sr":{"posa":180.000,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 202.5
==> {"gc":"G0 A202.5"}
{"r":{},"f":[1,0,19,78]}
{"sr":{"posa":180.005,"vel":63.95,"stat":5}}
{"sr":{"posa":202.500,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 225
==> {"gc":"G0 A225"}
{"r":{},"f":[1,0,17,76]}
{"sr":{"posa":202.505,"vel":63.95,"stat":5}}
{"sr":{"posa":225.000,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 247.5
==> {"gc":"G0 A247.5"}
{"r":{},"f":[1,0,19,78]}
{"sr":{"posa":225.005,"vel":63.95,"stat":5}}
{"sr":{"posa":247.500,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 270
==> {"gc":"G0 A270"}
{"r":{},"f":[1,0,17,76]}
{"sr":{"posa":247.505,"vel":63.95,"stat":5}}
{"sr":{"posa":270.000,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 292.5
==> {"gc":"G0 A292.5"}
{"r":{},"f":[1,0,19,78]}
{"sr":{"posa":270.005,"vel":63.95,"stat":5}}
{"sr":{"posa":292.500,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 315
==> {"gc":"G0 A315"}
{"r":{},"f":[1,0,17,76]}
{"sr":{"posa":292.505,"vel":63.95,"stat":5}}
{"sr":{"posa":315.000,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 337.5
==> {"gc":"G0 A337.5"}
{"r":{},"f":[1,0,19,78]}
{"sr":{"posa":315.005,"vel":63.95,"stat":5}}
{"sr":{"posa":337.500,"vel":0.00,"stat":3}}
ReadyEvent stat
CNC_A_m, a: 360
==> {"gc":"G0 A360"}
{"r":{},"f":[1,0,17,76]}
{"sr":{"posa":337.505,"vel":63.95,"stat":5}}
{"sr":{"posa":360.000,"vel":0.00,"stat":3}}
ReadyEvent stat
Stored calibration for nozzle 2
==> {"gc":"G0 Z0"}
{"r":{},"f":[1,0,15,74]}
{"sr":{"posz":37.454,"vel":0.21,"stat":5}}
{"sr":{"posz":31.303,"vel":1000.00}}
{"sr":{"posz":23.141}}
{"sr":{"posz":14.979}}
{"sr":{"posz":6.817}}
{"sr":{"posz":0.015,"vel":68.36}}
{"sr":{"posz":0.000,"vel":0.00,"stat":3}}
ReadyEvent stat
A: 0.000, X: 0.018, Y: 0.073
A: 22.500, X: 0.000, Y: 0.073
A: 45.000, X: -0.036, Y: 0.091
A: 67.500, X: -0.073, Y: 0.073
A: 90.000, X: -0.109, Y: 0.073
A: 112.500, X: -0.127, Y: 0.037
A: 135.000, X: -0.127, Y: 0.000
A: 157.500, X: -0.109, Y: -0.037
A: 180.000, X: -0.073, Y: -0.037
A: 202.500, X: -0.036, Y: -0.073
A: 225.000, X: 0.000, Y: -0.073
A: 247.500, X: 0.018, Y: -0.055
A: 270.000, X: 0.036, Y: -0.018
A: 292.500, X: 0.073, Y: 0.000
A: 315.000, X: 0.054, Y: 0.037
A: 337.500, X: 0.054, Y: 0.073
A: 360.000, X: 0.018, Y: 0.073
Bad data in warning treshold

Hello.
You need to set a value of eg 0.5 in the field "warning threshold"

Regards.

Krzysztof

As Krzysztof said.

Setting a number in a box that is larger than the wobble of the tip but not much larger (eye accuracy is fine) will give you a warning if a calibration value is bigger, guarding against possible vision errors. With no data there, you don't get warnings, but that doesn't prevent the calibration running.

Thanks.

Also, that box gets cleared out on every restart of the app

Jet wrote:Thanks.

Also, that box gets cleared out on every restart of the app

Fixed in the next release. Thank you for pointing that out.