Hi all,
after finishing the basic setup I tried to place some parts using the Hello World example.
After setting up the tape, I performed a homing, a Re-measure and a needle calibration. An alingment test of the tape position shows this result, not that bad I would say.
But the result is not what I expected, tried a couple of times, with and without Slack compensation, used different needles (blue, purple), but nearly the same result every time.
I have repeated the basic setup a couple of times to be sure that I did not missed something.
May be some one has an idea what went wrong and how to fix it ?
Placing components does not work
-
- Posts: 14
- Joined: Sat Jun 04, 2016 6:29 pm
- Location: Near Stuttgart, Germany
Placing components does not work
Last edited by caprisonne on Sat Jul 09, 2016 9:44 am, edited 2 times in total.
Re: Placing components do not work
Can you post your "hello world.csv"? I know it is downloaded from here... but I'd still like to see it. I noticed some oddities in different versions that I've downloaded.
-
- Posts: 14
- Joined: Sat Jun 04, 2016 6:29 pm
- Location: Near Stuttgart, Germany
Re: Placing components do not work
Sure,
Ref;Footprint;X;Y;Layer;Rotation;Comment
U1;SOIC-8;18.75mm;6.25mm;T;360.00;8-pin IC
Fid4;testFid;36.25mm;5mm;T;360.00;fiducial
Fid3;testFid;37.5mm;33.75mm;T;360.00;fiducial
Fid2;testFid;3.75mm;36.25mm;T;360.00;fiducial
Fid1;testFid;3.75mm;3.75mm;T;360.00;fiducial
R4;805;22.25mm;20.25mm;T;330.00;300R
R6;805;28mm;20.25mm;T;30.00;300R
R5;805;25mm;15.5mm;T;270.00;300R
R3;603;13mm;21mm;T;60.00;4k7
R2;603;12.75mm;16.5mm;T;300.00;4k7
R1;603;9mm;18.75mm;T;180.00;4k7
Ref;Footprint;X;Y;Layer;Rotation;Comment
U1;SOIC-8;18.75mm;6.25mm;T;360.00;8-pin IC
Fid4;testFid;36.25mm;5mm;T;360.00;fiducial
Fid3;testFid;37.5mm;33.75mm;T;360.00;fiducial
Fid2;testFid;3.75mm;36.25mm;T;360.00;fiducial
Fid1;testFid;3.75mm;3.75mm;T;360.00;fiducial
R4;805;22.25mm;20.25mm;T;330.00;300R
R6;805;28mm;20.25mm;T;30.00;300R
R5;805;25mm;15.5mm;T;270.00;300R
R3;603;13mm;21mm;T;60.00;4k7
R2;603;12.75mm;16.5mm;T;300.00;4k7
R1;603;9mm;18.75mm;T;180.00;4k7
Re: Placing components do not work
Looks like your rotation direction/smount is off. Please double check: Alt+Shift+F10 should be 90 degrees clockwise.
-
- Posts: 14
- Joined: Sat Jun 04, 2016 6:29 pm
- Location: Near Stuttgart, Germany
Re: Placing components do not work
Thanks for your answer!
One question: Does "clockwise" means: view from top-down direction or bottom-up direction?
Thanks in advance!
One question: Does "clockwise" means: view from top-down direction or bottom-up direction?
Thanks in advance!
Re: Placing components do not work
Top down.
-
- Posts: 14
- Joined: Sat Jun 04, 2016 6:29 pm
- Location: Near Stuttgart, Germany
Re: Placing components does not work
Hi,
we tried it again, but the problem isn't been solved.
With a rotation <= 90 dregrees, the components have been placed mostly accurate.
With a rotation > 90 Degrees the are mistakes as shown on the picture.
Could this be a hardware or a software problem?
Thanks in advance!
we tried it again, but the problem isn't been solved.
With a rotation <= 90 dregrees, the components have been placed mostly accurate.
With a rotation > 90 Degrees the are mistakes as shown on the picture.
Could this be a hardware or a software problem?
Thanks in advance!
Last edited by caprisonne on Fri Jul 15, 2016 1:23 pm, edited 1 time in total.
Re: Placing components does not work
The software has been in use for more than a year. I would be very surprised if we would discover a bug in so fundamental area, I would think that this is a hardware issue.
There is a Test A button on the basic setup tab. It turns the A axis full turn and back. Also the there are buttons that move x, y and a simultaneously. These are to ensure that the mechanics work on full range of machine movements and that the current settings and power supply capacity are sufficient.
Hint: It is difficult to see the A axis movement unless you put a piece of tape on the tube or (as I did) draw a mark on the pulley.
There is a Test A button on the basic setup tab. It turns the A axis full turn and back. Also the there are buttons that move x, y and a simultaneously. These are to ensure that the mechanics work on full range of machine movements and that the current settings and power supply capacity are sufficient.
Hint: It is difficult to see the A axis movement unless you put a piece of tape on the tube or (as I did) draw a mark on the pulley.
Re: Placing components does not work
Hi caprisonne,
maybe your TinyG config is messed up?
Try sending the following command to it: $4po=0
This will make sure A-axis motor is driven as intended (not inverted).
Then make sure to have the wiring correct; increasing A angle should turn needle counter-clockwise (looking from above).
Make sure the part rotation in tape setup is correct.
Also, check your E-CAD program file (CSV) for corect rotation values. The preview in Juha's software should be helpful.
Use this for reference:
Good luck!
maybe your TinyG config is messed up?
Try sending the following command to it: $4po=0
This will make sure A-axis motor is driven as intended (not inverted).
Then make sure to have the wiring correct; increasing A angle should turn needle counter-clockwise (looking from above).
Make sure the part rotation in tape setup is correct.
Also, check your E-CAD program file (CSV) for corect rotation values. The preview in Juha's software should be helpful.
Use this for reference:
Good luck!
Re: Placing components does not work
hi...i am a new user here. As per my knowledge there is a Test A button on the basic setup tab. It turns the A axis full turn and back. Also the there are buttons that move x, y and a simultaneously. These are to ensure that the mechanics work on full range of machine movements and that the current settings and power supply capacity are sufficient.It is difficult to see the A axis movement unless you put a piece of tape on the tube or (as I did) draw a mark on the pulley.